The Breakpoint: Why Harder Is Not Faster
For decades cyclists believed harder tyres were faster tyres, and pumped narrow tyres to 110 PSI or more. The Silca impedance model showed why that is wrong. A tyre has two sources of resistance: hysteresis (the energy lost as the casing flexes) and impedance (the energy lost as the whole bike vibrates over bumps). Higher pressure reduces hysteresis — the tyre flexes less — but increases impedance, because a rock-hard tyre bounces over every bump instead of absorbing it, and the rider’s body absorbs the vibration. The sum of the two has a minimum: the breakpoint. Below it, more pressure helps; above it, more pressure hurts. On real roads the breakpoint for a 28 mm tyre sits near 60–70 PSI, far below the 110 PSI that used to be standard. On a perfectly smooth wooden velodrome the breakpoint is higher, which is why track riders still run high pressures — and why road advice taken from the track is wrong.
Worked Example: 28 mm Tubeless for an 80 kg Rider
Take an 80 kg rider on 28 mm tubeless road tyres. The calculator gives about 61 PSI (4.2 bar) for the front wheel and 68 PSI (4.7 bar) for the rear. The rear runs higher because it carries more of the rider’s weight — roughly 60% rear, 40% front. The same rider on 25 mm tyres would need about 10 PSI more, and on 32 mm tyres about 8 PSI less, because wider tyres spread the load over a bigger contact patch and need less pressure to hold their shape. These are starting points for smooth tarmac: drop 2–3 PSI for wet roads (more grip), drop 5 PSI or more for rough roads and gravel (let the tyre absorb the surface), and add a little for a loaded touring bike or a heavier rider. Check the pressure before every ride — tyres lose 5–10 PSI a week through the casing, and a tyre that was right last Sunday is soft today.
What Changes the Right Pressure?
Four things move the number. Rider weight: a 100 kg rider needs roughly 15% more pressure than a 70 kg rider on the same tyres. Tyre width: wider is lower — a 32 mm tyre at 55 PSI rides like a 25 mm tyre at 80 PSI, and rolls faster on rough roads. Surface: rough tarmac, cobbles and gravel all lower the breakpoint, so lower pressure is faster there; smooth tarmac raises it. Casing: supple tubeless casings flex more easily and run lower pressures than stiff clinchers, and latex inner tubes lose air faster than butyl. The silica in modern tread compounds matters too: silica-reinforced rubber grips better when wet and rolls with less hysteresis, which is why the same tyre in a silica compound can run a few PSI lower than an old carbon-black tyre. The calculator models all of this — weight, measured width (not the printed size, which is often wrong), surface and casing — instead of a single pressure chart.
Car Tyres: Cold Pressure and the Ideal Gas Law
Car tyres follow the same physics with different numbers. Pressure rises with temperature — the ideal gas law says pressure is proportional to absolute temperature, so a tyre at 32 PSI on a cold morning reads about 35 PSI after a motorway run, and drops about 1 PSI for every 10°F (5.5°C) the temperature falls. That is why every car maker says to check pressures cold, before driving, and monthly: a tyre that is 5 PSI low wears its edges, uses more fuel and handles worse, and in winter the cold alone can take a correctly inflated tyre below the recommended pressure. The pressure on the door sticker is the cold pressure for the car’s normal load, not the maximum on the sidewall — the sidewall number is the tyre’s limit, not the target. Check monthly with a gauge you trust; dashboard systems warn late, usually only when a tyre is 25% low.
Tubeless vs. Clincher, and Sealant
Tubeless tyres have no inner tube: the tyre seals directly against the rim, and sealant inside plugs small punctures as they happen. Because there is no tube to pinch, tubeless tyres can run 5–10 PSI lower than clinchers of the same width without pinch flats, which is exactly the direction the breakpoint points. The trade-off is setup: tubeless tyres need compatible rims, sealant topped up every few months, and a burst of air to seat the bead the first time. Clinchers with tubes are simpler and easier to fix at the roadside, but they pinch-flat when they hit a sharp edge at low pressure. Whichever system you run, the pressure logic is the same — find the breakpoint for your weight, width and surface, and stay just under it.
How to Get It Right
Measure your real tyre width with callipers — a tyre printed 28 mm often measures 30 mm on a wide rim, and the calculator wants the measured width. Weigh yourself with the bike and your usual kit, not just your body weight. Start at the calculator’s pressure, then adjust by feel: if the bike feels harsh and skittish on rough roads, drop 2–3 PSI; if it feels squirmy in corners or the rim hits bumps, add 2–3 PSI. Keep a floor pump with a gauge at home and a small pump on the bike, and check before every ride. The right pressure is not a badge of honour — it is the pressure that is fastest and most comfortable on your roads, and it is almost always lower than you think.