Construction & Home ImprovementLast reviewed: November 2026

Retaining Wall Calculator

A retaining wall calculator estimates how many concrete blocks, how much levelling-pad material and how much drainage gravel a landscape wall needs. Enter the length, height and block size, and it counts the buried base course too, and flags geogrid reinforcement on walls 4 feet tall or higher.

Key facts:
  • Walls 4 feet and taller usually need engineering and geogrid.
  • A 40-ft by 3-ft wall with 12 by 4-inch blocks needs 400 blocks.
  • Bury at least one full course below grade for stability.
  • Always include a 12-inch gravel drainage zone and pipe behind the wall.

Loading calculator…

Share or Export Current Results

Share Retaining Wall Calculator directly or copy link to clipboard

TwitterLinkedInFacebookWhatsApp

Calculation Formula & Mathematical Engine

Theoretical equation governing this computation.

Blocks = \left(\frac{Length_{ft} \times 12}{BlockL_{in}}\right) \times \left(\frac{Height_{in} + Buried_{in}}{BlockH_{in}}\right)

Variable Definitions

BlocksTotal concrete retaining wall blocks
Length_{ft}Total linear wall length along contour
Height_{in}Exposed wall height above grade
Buried_{in}Embedment base depth (minimum 1 buried course for stability)

Step-by-Step Calculation Example

40-Foot Long, 3-Foot High Landscape Retaining Wall

Scenario: Building a 40-foot wall with 12"×4" concrete segmental blocks with 1 buried base course.
Wall Length40 linear ft
Visible Height3.0 ft (36 inches)
Block Dimensions12" L × 4" H
Buried Courses1 Course (4 inches)
Execution Steps
  1. 1Total wall height: 36" + 4" = 40 inches (10 courses)
  2. 2Blocks per course: (40 × 12) ÷ 12 = 40 blocks
  3. 3Total blocks: 10 courses × 40 blocks = 400 blocks
  4. 4Drainage gravel chimney: 40 ft × 1 ft × 3 ft = 120 cu ft ÷ 27 × 1.35 = 6.0 tons
Final Verified Output:400 Retaining Wall Blocks + 6.0 Tons #57 Drainage Gravel

How to Build a Segmental Retaining Wall

Follow these steps to get your result.

  1. 1Measure the wall length and height, and choose your block size.
  2. 2Enter the dimensions to get the block count, buried base course and drainage gravel tonnage.
  3. 3Dig a trench and compact a 6-inch crushed-stone levelling pad.
  4. 4Lay the buried base course perfectly level, then stack the blocks with a slight setback.
  5. 5Backfill a 12-inch zone of clean gravel with a perforated pipe at the base, and finish with cap blocks.

Comprehensive Practical Guide

In-depth analysis, domain guidelines, standard practices, and common pitfalls.

Why Walls Above 4 Feet Require Engineering

Hydrostatic pressure from wet soil can topple retaining walls. Municipal building codes universally require geotechnical engineering and geogrid soil reinforcement for walls exceeding 4 feet.

How Much Gravel Goes Behind a Retaining Wall?

Allow a 12-inch-wide chimney of clean #57 drainage stone directly behind the wall, from the base to within 6 inches of the top, with a perforated pipe at the base draining to daylight. The worked example — a 40 ft wall, 3 ft high — needs about 6.0 tons of drainage gravel. Water pressure behind the wall is the number one cause of retaining wall failure, so never backfill with clay or soil alone.

Frequently Asked Questions About Retaining Wall Calculator

Direct, verified answers to common calculation and methodology questions.

No. Segmental retaining walls are dry-stacked systems held in place by friction, rear locking lips, or fiberglass alignment pins.
Authoritative Sources & Data References:
  • National Concrete Masonry Association (NCMA Design Manual)
  • International Building Code (IBC Section 1807)

Disclaimer: Retaining walls exceeding 4 feet require structural engineering calculations.